Ic Audio 9700

Stereo audio from IC-9700 - klop.solutions

https://klop.solutions/stereo-audio-from-ic-9700/

Stereo audio from IC-9700. Icom’s new IC-9700 can receive two bands at the same time. In DV mode, it can decode two digital signals at the …

Icom IC-9700, IC9700 GigaParts.com

https://www.gigaparts.com/icom-ic-9700-vhf-uhf-transceiver.html

8 Reasons to/NOT to Buy Icom IC-9700 - The American QRP Club

https://amqrp.org/icom-ic-9700/

D-STAR support – The IC-9700 supports both DV (Digital Voice) and DD (Digital Data) through D-STAR, making it a great option for hams who want to get started with digital radio. It also supports up to 99 satellite channels. 100w maximum power output – The IC-9700 transmits at 100w on the 144 MHz band, 75w on the 430/440MHz bands, and 10w on ...

IC-9700 VHF/UHF Transceiver - Features - Icom America

http://www.icomamerica.com/en/products/amateur/hf/9700/default.aspx

Built with the VHF/UHF weak signal operator in mind, the IC-9700 is an RF direct sampling receiver for 2m and 70cm. The IF receiver consists of a single, down conversion for 23cm that is between 311 – 371MHz. This design provides a quiet receiver due to Icom’s DSP technology. The robust PA provides 100W on 2m, 75W on 70cm, and 10W on 23cm.

IC-9700 User Evaluation & Test Report - AB4OJ

https://www.ab4oj.com/icom/ic9700/9700notes.pdf

1 IC-9700 User Evaluation & Test Report By Adam Farson VA7OJ/AB4OJ Iss. 5, Mar.19, 2021. Figure 1: The Icom IC-9700. Introduction: This report describes the evaluation of IC-9700 S/N 12001793 from a user perspective. Appendix 1 presents results of an RF lab test suite performed on the radio. As my VHF/UHF antenna facilities are very limited, I was unable to do much in the …

ICOM IC-9700 ICOM IC-9700 VHF/UHF/1.2 GHz …

https://www.dxengineering.com/parts/ico-ic-9700

Icom IC-9700 PTT Breakout Mod (or, “the parts Icom forgot ...

https://thehamlab.com/2021/12/29/icom-ic-9700-ptt-breakout-mod/

Icom IC-9700 PTT Breakout Mod (or, “the parts Icom forgot”) December 29, 2021. December 29, 2021. Alex KR1ST. If you’ve used the IC-9700 with amplifiers, you no doubt realized that it would have been convenient if Icom would have provided a separate PTT output signal for each band. For about 5 dollars in parts they could have done this ...

Icom IC-9700 Power overshoot – PH4X

https://www.ph4x.com/icom-ic-9700-power-overshoot/

Alse the IC-9700 is equipped with the famous ‘power overshoot’ or ‘ALC overshoot’ issue most modern Icom transceivers have. Apparently Icom can’t get a grip on this issue. Bad news for people using transistor based amplifiers (SSPA) in SSB mode. Since the IC-9700 had a ‘TX PWR LIMIT’ function, setting this to 7%* will prevent the ...

ICOM IC-9700 Transceivers Other, IC9700 - Ham Radio Outlet

https://www.hamradio.com/detail.cfm?pid=H0-016656

Specifically built for the VHF/UHF weak signal operator in mind, the IC-9700 is a RF direct sampling receiver for 2m and 70cm, with a single, down conversion for 23cm with an IF Sampled receiver between 311 – 371MHz. This design provides a quiet receiver with the power of Icom’s DSP technology along with a robust PA providing 100W on 2m ...

IF output on IC-7300 and IC-9700 - klop.solutions

https://klop.solutions/if-output-on-ic-7300-and-ic-9700/

IF output on IC-7300 and IC-9700. Both the IC-7300 and the IC-9700 have an IF output option. A great feature that enables the receive of all kinds of exotic transmissions. On the IC-7300, Icom pitched this feature at DRM receive. Soon after the IC-7300 launched, it became clear that the IF output bandwidth varies with the receive mode setting ...