We have collected the most relevant information on Wsjt Audio Setup. Open the URLs, which are collected below, and you will find all the info you are interested in.
WSJT SETUP - QSL.net
https://www.qsl.net/zr6dxb/Digital/wsjtsetup.htm#:~:text=1.%20Install%20and%20launch%20WSJT%20Software.%202.%20Click,port%20you%20are%20using.%203.%20Next%20click%20SETUP%2FOPTIONS
Setting up CAT/CI-V and Audio Drivers for WSJT-X
https://www.n1fd.org/2018/11/26/wsjt-x-setup/
The settings you select in Device Manager Properties must be used in the WSJT-X setup. Once these settings are set for the COM port and in the WSJT-X app consider them set, and leave them. If you have completed these steps and do not have CAT/CI-V control of the radio it is due to incorrect radio settings, a bad/cheap cable, you are connected through an …
WSJT-X audio setup | QRZ Forums
https://forums.qrz.com/index.php?threads/wsjt-x-audio-setup.740350/
File ---> Settings ---> Audio ---> Input: Mikrofon (3 - C-Media USB Audio Device); Output Reproduktory (3 - C-Media USB Audio Device); both set to mono Mikrofon = Mike Reproduktory = Speakers
WSJT-X v1.4 Configuration Guide – W4TI- Whiskey Four …
http://w4ti.com/wsjt-x-help-files/wsjt-x-configuration-guide/
WSJT-X Configuration Guide. After installing WSJT-X, the user must configure the program with some basic information. There are six different areas, or “tabs,” which are located under the main Configuration menu: General , Radio, Audio , Tx Macros, Reporting and Frequencies. Some of these tabs contain options which are necessary to input or select (i.e. your Call Sign and Grid …
WSJT SETUP - QSL.net
https://www.qsl.net/zr6dxb/Digital/wsjtsetup.htm
Install and launch WSJT Software. 2. Click SETUP/SET COMM PORT and put in the serial port you are using. 3. Next click SETUP/OPTIONS 4. In options page put in: MY CALL = your call sign GRID LOCATER = your 6 digit grid locator (Put in you grid like this KG33xx not KG33XX) UTC OFFSET = leave at zero (default) to have WSJT display local time, or put in your UTC
Setting Audio Levels For Digital Modes – Digirig
https://digirig.net/setting-audio-levels-for-digital-modes/
Audio from Radio to Computer 1.1. Enable line audio output. Your Digirig is typically hooked up to the the auxiliary audio connector. Some... 1.2. Set RF gain control to automatic. The level of incoming RF signal from your antenna varies greatly. These... 1.3. Set line out …
WSJT-X User Guide - Princeton University
https://www.physics.princeton.edu/pulsar/k1jt/wsjtx-doc/wsjtx-main-1.7.0.html
Mode: WSJT-X uses upper sideband mode for both transmitting and receiving. Select USB, or choose Data/Pkt if your radio offers such an option and uses it to enable the rear-panel audio line input. Some radios also offer wider and/or flatter passbands when set to Data/Pkt mode. Select None if you do not want WSJT-X to change the radio’s Mode setting.
WSJT-X 2.2 User Guide
https://physics.princeton.edu/pulsar/k1jt/wsjtx-doc/wsjtx-main-2.2.1.html
Mode: WSJT-X uses upper sideband mode for both transmitting and receiving. Select USB, or choose Data/Pkt if your radio offers such an option and uses it to enable the rear-panel audio line input. Some radios also offer wider and/or flatter passbands when set to Data/Pkt mode. Select None if you do not want WSJT-X to change the radio’s Mode setting.
Using WSJT-X with SDRUNO and RSP1A
http://www.ve6kq.com/wsjtandsdruno.pdf
control on the SDRUno rx control module will control the audio level into the WSJT-X software. The following should be done in order otherwise there is a good change WSJT-X won’t run. See screen shots below for support of the following steps. You will need to run the Virtual Serial Port Emulator (VSPE) first. Next install SDRUNO.
https://groups.io/g/FT8-Digital-Mode/topic/no_output_from_wsjt_x/29630957?20,0,0,0::recentpostdate%2Fsticky,,,20,2,0,29630957
WSJT-X is working fine on rx. I am not getting any output from WSJT-X on tx. I observe no output when I click Tune - no audio when radio Monitor is on, and no output if I take the sound card output to a speaker. The sound card works. I have tried this with an Elecraft and an internal sound card and an FT1000mp and an external sound card.
Configuring WSJT-X and SmartSDR for Windows – FlexRadio
https://helpdesk.flexradio.com/hc/en-us/articles/202037343-Configuring-WSJT-X-and-SmartSDR-for-Windows
Go to the Setup Configuration page in WSJT-X. Here's how mine is setup: The General tab setup. The Radio tab setup . NOTE: Select the TS-2000 as the rig for CAT. The Audio tab setup. Once you have this done, you should click OK and then go look at the waterfall in WSJT-X. You should see that you have audio from the radio and WSJT-X should start decoding.
Now you know Wsjt Audio Setup
Now that you know Wsjt Audio Setup, we suggest that you familiarize yourself with information on similar questions.
