We have collected the most relevant information on Signalink Audio Bleed. Open the URLs, which are collected below, and you will find all the info you are interested in.
SignaLink USB Troubleshooting - Tigertronics
https://www.tigertronics.com/slusbts.htm
Verify that the SignaLink USB’s PWR LED is ON. If it is not, then make sure that the SignaLink USB's PWR switch is pressed in and the USB cable is securely connected to the computer and the SignaLink. If the PWR indicator still won't turn ON, then try changing USB cables, USB ports, or using a different computer.
SignaLink Support - Tigertronics
https://tigertronics.com/sl_suprt.htm
SignaLink USB Audio Transformers and Other Changes We have been shipping wider bandwidth surface mount (SMT) isolation transformers (click for a picture) in the SignaLink USB since ~June 2018. The .25db bandwidth of the transformers is 200Hz to 4000Hz. The normally specified 3db bandwidth of these transformers and the SignaLink USB as a whole ...
SignaLink USB Interface - Tigertronics
http://www.tigertronics.com/slusbmain.htm
The SignaLink USB provides isolation through the use of audio transformers and a relay-based PTT keying circuit. Transmit Audio / "Side Tone" Output - A rear panel "Monitor" jack can be used with headphones or powered (amplified) speakers to monitor your Transmit Audio, or Side Tone during CW operation.
Signalink and Other USB Digital Interfaces Huge Bug Fix ...
https://k3rrr.com/signalink-and-other-usb-digital-interfaces-huge-bug-fix-for-amateur-radio-digital-modes/
On the radio device, such as your SignaLink, click properties. Then go to the levels tab. Right click on the slider and change the value from Percentage to DB. If 100% on the slider reads +30db, you are affected by the bug. If the device was properly enumerated as a line in device, 100% on the slider would be 0db.
SignaLink USB Manual - QSL.net
https://www.qsl.net/kb7tbt/manuals/Tigertronics/SignaLinkUSB.pdf
SignaLink’s Transmit Audio signal. The output level of this jack varies with the computer’s software volume controls, and provides a maximum level of approximately 400mv p-p into 1Kohm. This is sufficient to drive most amplified speakers …
Setup Instructions - Communication Programs - Tigertronics
https://www.tigertronics.com/pgmsetup.htm
Sound Card Selection - This MUST always be set to the SignaLink's "USB Audio Codec" sound card, and you will usually need to set both the output / playback (Transmit) and input / capture (Receive) sound card separately. In Windows Vista/7/8.x/10, the SignaLink USB's sound card is shown as "Microphone - USB Audio Codec" for the input / capture ...
SignaLink Jumper Settings & Wiring Information - Tigertronics
https://www.tigertronics.com/sl_wirebm.htm
The SignaLink USB is always powered by the computer and never needs external power. **Speaker Audio is not available on the Mic jack of this radio, so do NOT install the SPKR jumper wire. Instead, use the supplied audio cable as detailed in the SignaLink USB manual.
AGWPE and the SignaLink USB - Sound Card Packet
https://soundcardpacket.org/7signalinkusb.aspx
If the SignaLink is plugged into an external USB hub, verify that the hub is a powered hub and is getting external power. Non-powered hubs may not supply enough power for the SignaLink to operate properly (Receive will work, but Transmit may not). b. No Received Audio in the AGWPE Sound Card Tuning Aid.
Yaesu FT-891 Setup for Digital Modes - KB9VBR Antennas
https://www.jpole-antenna.com/2020/08/12/yaesu-ft-891-setup-for-digital-modes/
My preference is to use the Signalink as it has two definite advantages over the patch cable route. First is that it provides audio isolation so you don’t end up with hum or ground loops. And the second is that system sounds won’t bleed into your operation as they will be routed through the computer’s audio device.
decode digital signals | QRZ Forums
https://forums.qrz.com/index.php?threads/decode-digital-signals.555951/
There is a little bit of bleed-through of the radio signals through the resistors and caps that surround the op-amps, and that allows a little bit of signal to get through to the codec. If the S/N is high enough coming from your radio, this bleed-through audio is good enough to let your sound-card decode the digimode signal.
Now you know Signalink Audio Bleed
Now that you know Signalink Audio Bleed, we suggest that you familiarize yourself with information on similar questions.
