We have collected the most relevant information on Pulseaudio Rtp Documentation. Open the URLs, which are collected below, and you will find all the info you are interested in.
How to listen to the pulseaudio RTP Stream - freedesktop.org
https://freedesktop.org/wiki/Software/PulseAudio/Documentation/User/Network/RTP/
You should change the configuration file default.pa to send the RTP traffic to 127.0.0.1 and a specific port (in my case 46998) load-module module-null-sink sink_name=rtp format=s16be channels=2 rate=44100 description="RTP Multicast Sink" load-module module-rtp-send source=rtp.monitor destination=127.0.0.1 port=46998 loop=1. Log off and back on ...
pulseaudio: pa_rtp_context Struct Reference - doxygen ...
https://fossies.org/dox/pulseaudio-15.0/structpa__rtp__context.html
Fossies Dox: pulseaudio-15.0.tar.xz ("unofficial" and yet experimental doxygen-generated source code documentation) Data Fields pa_rtp_context Struct Reference
Use PulseAudio and RTP to stream audio within your local ...
http://www.kikeriki.at/pulseaudio-rtp.html
Install both using. # pacman -S pulseaudio-rtp pulsemixer. Find out the IP address of the device you want to send audio to and load the rpt-send module using. $ pactl load-module module-rtp-send port=4444 destination_ip=192.168.1.3. On the receiving side I …
PulseAudio/Examples - ArchWiki
https://wiki.archlinux.org/title/PulseAudio/Examples
For a more detailed guide visit the Official PulseAudio Documentation. Enable the TCP module on the server(the computer that actually outputs sound), edit /etc/pulse/default.pa to add or uncomment: load-module module-native-protocol-tcp ... To use RTP in pulseaudio on archlinux, install pulseaudio-rtp on the remote and local servers.
Use Pulseaudio to stream audio file to network via RTP ...
https://gist.github.com/porjo/5cce51d80b349b984d5e8c1c95066c1a
Play + Listen to Audio. Pipe Audio File to RTP sink: sox -e signed-integer -b 16 -r 16000 -c 1 <input filename> -t pulseaudio rtp. Receive Audio From RTP sink monitor: parec -d rtp.monitor --rate=16000 --channels=1 | aplay -t raw -f S16_LE -r 16000. (for some reason using sox for playback I was getting glitchy audio with buffer underruns)
PulseAudio RTP – how to play sound on sender too – iTecTec
https://itectec.com/unixlinux/pulseaudio-rtp-how-to-play-sound-on-sender-too/
Finally, on the sender, make it a receiver too: You can make the configuration on the receivers permanent by editing /etc/pulse/default.pa. To stop RTP casting to the receivers, run this script on the sender: For starting and stopping music play, no changes are needed on the receivers. Their config can be made permanent.
PulseAudio RTP and cVLC Transcoding / Multimedia and Games ...
https://bbs.archlinux.org/viewtopic.php?id=209801
Anyway, after saving the `default.pa` config file and restarting pulseaudio I then begin transcoding with cVLC to stream the RTP stream as MP3 for lower bandwidth consumption, as described in the Freedesktop doc linked above: cvlc rtp://@127.0.0.1:47777 ":sout=#transcode {acodec=mp3,ab=256,channels=2}:duplicate {dst=rtp {dst=225.0.0.1,mux=ts ...
Now you know Pulseaudio Rtp Documentation
Now that you know Pulseaudio Rtp Documentation, we suggest that you familiarize yourself with information on similar questions.
