We have collected the most relevant information on Pulseaudio Remote Output. Open the URLs, which are collected below, and you will find all the info you are interested in.
networking - How to set up PulseAudio remote properly …
https://unix.stackexchange.com/questions/470961/how-to-set-up-pulseaudio-remote-properly-and-securely
Under the Output Devices tab, you should see the local and remote output devices." However, when doing that, I did not see any remote output devices on the client. I had to open paprefs in a terminal and do the following extra steps: Network Access tab on client: check Make discoverable PulseAudio network sound devices available locally
PulseAudio/Examples - ArchWiki - Arch Linux
https://wiki.archlinux.org/title/PulseAudio/Examples
Restart PulseAudio, run pavucontrol and select the "Output Devices" tab. Three settings should be displayed: Internal Audio Digital Stereo (HDMI) Internal Audio Simultaneous output to Internal Audio Digital Stereo (HDMI), Internal Audio Now start a program that will use PulseAudio such as MPlayer, VLC, mpd, etc. and switch to the "Playback" tab.
Streaming audio output from Linux (Pulseaudio) to …
https://gist.github.com/Fusl/3a708b8c32c9d5264fa0
pactl load-module module-null-sink sink_name=remote: ffmpeg -f pulse -i "remote.monitor" -ac 2 -acodec pcm_u8 -ar 48000 -f u8 "udp://RECEIVER:18181" pavucontrol # Change the default output to the Null sink or move single applications to this "output" device.
PulseAudio as remote source *and* sink? - Unix & Linux ...
https://unix.stackexchange.com/questions/624220/pulseaudio-as-remote-source-and-sink
On the reciever sides, create an RTP source: load-module module-null-sink sink_name=rtp load-module module-rtp-recv sink=rtp set-default-source rtp_monitor Now the audio data will be available from the default source rtp_monitor. This can help you with the setup. You will have to add both the input sink and the output one.
vlc - Pulseaudio to output RTP to internet - Stack Overflow
https://stackoverflow.com/questions/14452675/pulseaudio-to-output-rtp-to-internet
I want pulseaudio (remote instance) to push audio sent to the primary alsa device straight to RTP over the internet so that I could listen to it on VLC on my home computer. in my /etc/pulse/default.pa. load-module module-rtp-send source=alsa_output.0.analog-stereo.monitor destination=x.x.x.x port=8080 loop=1
PulseAudio | Music Player Daemon Wiki | Fandom
https://mpd.fandom.com/wiki/PulseAudio
First remove the MPD PulseAudio setting. Configure MPD to use esd as shown, this assumes that MPD and PulseAudio are running on the same system. audio_output { type "ao" driver "esd" options "host=127.0.0.1:16001" name "esd" } Another solution found at Ubuntuforums.org is to replace the "ao" with "pulse", which works in some cases where ao fails.
PulseAudio - Official Kodi Wiki
https://kodi.wiki/view/PulseAudio
PulseAudio can be run in one of two modes these are: Passthrough Mode Used if you want to passthrough (bitstream) AC3, DTS, and EAC3 to an AVR or other device. In order to allow passthrough to work with PulseAudio then it MUST be set to use a 2.0 channel configuration, despite the 2.0 setting this will still allow 5.1 audio from AC3, DTS, and EAC3.
How To Get The Sound (PulseAudio) To Work On WSL2 ...
https://codepre.com/how-to-get-the-sound-pulseaudio-to-work-on-wsl2.html
Start the PulseAudio Windows service. Start the Windows Task Manager and click Services Tab and scroll to PulseAudio.When you find the PulseAudio service, right-click on it and select Start it: We are done. PulseAudio is now working. You should be able to use audio-enabled applications in WSL2 and hear its audio output on the Windows 10 desktop.
Using PulseAudio as network sound server on Ubuntu and ...
https://www.techytalk.info/pulseaudio-network-sound-server/
Using your PC as PulseAudio network client Now you can open sound options on your client PC by pressing Alt+F2 and entering "gnome-volume-control" into the "Run Application" dialog. On the "Output" tab you should be able to select any of the devices on your server PC as well as any local sound device as output device.
xRDP – How to redirect Sound on Ubuntu 18.04 – …
https://c-nergy.be/blog/?p=12469
cd /tmp/pulseaudio* sudo ./configure Building the Pulseaudio Module. Since we have the necessary pulseaudio source in tmp directory, it’s time to compile them so they can be used by the xRDP software. To compile them, we will issue the following commands . cd /usr/src/xrdp-pulseaudio-installer make PULSE_DIR="/tmp/pulseaudio-11.1"
Now you know Pulseaudio Remote Output
Now that you know Pulseaudio Remote Output, we suggest that you familiarize yourself with information on similar questions.
