We have collected the most relevant information on Pulseaudio Per Session. Open the URLs, which are collected below, and you will find all the info you are interested in.
Fixing PulseAudio configured for per-user sessions ...
https://www.blackmoreops.com/2013/10/12/fixing-pulseaudio-configured-for-per-user-sessions-warning-in-kali-linux/
[warn] PulseAudio configured for per-user sessions ... (warning). Debian variants also throws similar warning during boot. To fix this do leafpad /etc/default/pulseaudio. Find this line: PULSEAUDIO_SYSTEM_START=0. Replace 0 with 1. PULSEAUDIO_SYSTEM_START=1. Where, 0 = don’t start in system mode, 1 = start in system mode. reboot. That should fix the …
[SOLVED] PulseAudio configured for per-user sessions ...
https://forums.kali.org/showthread.php?18321-SOLVED-PulseAudio-configured-for-per-user-sessions-(warning)
[SOLVED] PulseAudio configured for per-user sessions ... (warning). If this is your first visit, be sure to check out the FAQ by clicking the link above. You may have to register before you can post: click the register link above to proceed. To start viewing messages, select the forum that you want to visit from the selection below.
PulseAudio configured for per-user sessions ... (warning).
https://www.linuxquestions.org/questions/debian-26/pulseaudio-configured-for-per-user-sessions-warning-914796/
According to the PulseAudio Wiki, system wide mode is only recommended for minimalist installs (such as embedded clients) where there aren't really any users per say. System wide mode creates a few security issues. I believe it also disables a few features of PulseAudio. The recommended mode is per-user configuration.
PulseAudio configured for per-user sessions Warning ...
https://forums.debian.net/viewtopic.php?t=89120
Re: PulseAudio configured for per-user sessions Warning Post by Micket » 2013-01-27 05:56 While the original poster might really have wanted to run pulseaudio in system mode, I think its far more likely that everyone who goes around changing that setting really only wanted to start the pa daemon.
PulseAudio | Music Player Daemon Wiki | Fandom
https://mpd.fandom.com/wiki/PulseAudio
Solutions: To remedy cause 1, add user mpd to the pulseaudio groups so that mpd can even start pulseaudio on demand: $ sudo usermod -a -G pulse-access mpd $ sudo usermod -a -G pulse mpd $ sudo usermod -a -G pulse-rt mpd. To further fix cause 2, open your X11 session to mpd either by. xhost +local:mpd.
pulseaudio(1) — Arch manual pages
https://man.archlinux.org/man/pulseaudio.1
When PulseAudio runs in the per-user mode and detects a login session, then any positive value will be reset to 0 so that PulseAudio will terminate immediately on logout. A positive value therefore has effect only in environments where there's no support for login session tracking (or if the user is logged in without a session spawned, a.k.a. lingering).
pulseaudio - man pages section 1: User Commands
https://docs.oracle.com/cd/E88353_01/html/E37839/pulseaudio-1.html
Combine with -n to disable loading of the default script default.pa (see below). -C Open a command interpreter on STDIN/STDOUT after startup. This may be used to configure PulseAudio dynamically during runtime. Equivalent to --load=module-cli. -n Don't load default script file default.pa (see below) on startup.
pulseaudio man | Linux Command Library
https://linuxcommandlibrary.com/man/pulseaudio
When PulseAudio runs in the per-user mode and detects a login session, then any positive value will be reset to 0 so that PulseAudio will terminate immediately on logout. A positive value therefore has effect only in environments where there's no support for login session tracking (or if the user is logged in without a session spawned, a.k.a. lingering).
audio - How to get PulseAudio running? - Raspberry Pi ...
https://raspberrypi.stackexchange.com/questions/639/how-to-get-pulseaudio-running
I had a hard time getting pulseaudio running on Wheezy raspbian (2012-10-28) using the analog output. The following is what I did just …
Sway, XDG, D-Bus, Session, PulseAudio, systemd etc. …
https://www.reddit.com/r/swaywm/comments/ibainf/sway_xdg_dbus_session_pulseaudio_systemd_etc_need/
D-Bus session bus is also started automatically, but if you want to have multiple simultaneous sessions for the same user on the same machine, you may want to create own bus for each session. So the Sway command should be like this: XDG_SESSION_TYPE=wayland exec …
Now you know Pulseaudio Per Session
Now that you know Pulseaudio Per Session, we suggest that you familiarize yourself with information on similar questions.
