We have collected the most relevant information on Pulseaudio No Hardware Output Devices. Open the URLs, which are collected below, and you will find all the info you are interested in.
sound - PulseAudio not detecting any devices - Ask Ubuntu
https://askubuntu.com/questions/859773/pulseaudio-not-detecting-any-devices
Going to settings, it offered only "Dummy" output as output device. Here's what worked for me (first two steps from System76): Remove the configuration file of PulseAudio: rm -r ~/.config/pulse. Kill all instances of PulseAudio; pulseaudio …
pulseaudio no output devices / Newbie Corner / Arch Linux ...
https://bbs.archlinux.org/viewtopic.php?id=88194
Re: pulseaudio no output devices You probably tried to start pulseaudio with some app still having control of the sound card. Try using …
PulseAudio don't see Hardware output device - Hardware ...
https://archived.forum.manjaro.org/t/pulseaudio-dont-see-hardware-output-device/33087
PulseAudio don't see Hardware output device. Technical Issues and Assistance. Hardware. audio, sound, pulseaudio, alsa. kimal. 19 October 2017 12:54 #1. I use xfce. aplay show this card, but PulseAudio don't see it, what can i do? pixel27 18 October 2017 13:17 ...
PulseAudio has no sound, only has Dummy Output - Ask …
https://askubuntu.com/questions/1359038/pulseaudio-has-no-sound-only-has-dummy-output
What we need to do now is to force Ubuntu to use the analog output by default instead of the HDMI interface, and here we need some information. Open a terminal and enter the following command. aplay -l. The terminal will list the device, card number, etc. Write down the card number and the analog output device number.
Configuring Pulseaudio for Multiple Output Devices - Eliot ...
http://www.6by9.net/configuring-pulseaudio-for-multiple-output-devices/
Configuring Pulseaudio for Multiple Output Devices. ... you need to configure Pulseaudio to send output to the correct device. For this, ... HARDWARE DECIBEL_VOLUME LATENCY FLAT_VOLUME DYNAMIC_LATENCY state: SUSPENDED suspend cause: IDLE priority: 9059 volume: 0: 65% 1: 65% 0: -11.22 dB 1: -11.22 dB balance 0.00 base volume: 100% 0.00 dB …
Changing Output Device with PulseAudio - Reality's End
http://www.realitysend.com/log/linux/changing-output-device-with-pulseaudio
profiles: output:analog-stereo: Analog Stereo Output (priority 6000) output:analog-stereo+input:analog-stereo: Analog Stereo Duplex (priority 6060) output:hdmi-stereo: Digital Stereo (HDMI) Output (priority 5400) output:hdmi-stereo+input:analog-stereo: Digital Stereo (HDMI) Output + Analog Stereo Input (priority 5460) output:hdmi-surround: Digital Surround 5.1 …
PulseAudio shows "Dummy Output" - Speaker-test works ...
https://forums.debian.net/viewtopic.php?t=104263
The Pulseaudio volume control (pavucontrol) connects to Pulseaudio, but also only shows the "Dummy Output" device under Virtual devices. Selecting "Hardware output devices" results in a display of "No output devices available". Time for my dumb question: what happened to the default device in the aplay -L output and, more importantly, how do I get it …
Pipewire doesn't actually recognize any Sound outputs ...
https://ask.fedoraproject.org/t/pipewire-doesnt-actually-recognize-any-sound-outputs-devices/17021
# Enable pipewire and disable pulse sudo dnf install --allowerasing pipewire-pulseaudio systemctl --user start pipewire-pulse.service pipewire-pulse.socket # pavucontrol shows no sound devices, and provides no sound output # Disable pipewire and switch back sudo dnf swap --allowerasing pipewire-pulseaudio pulseaudio # Working again, pavucontrol shows …
pulseaudio: Switch between output devices without ...
https://www.reddit.com/r/linuxquestions/comments/pgdwo8/pulseaudio_switch_between_output_devices_without/
You probably had something else hogging your devices. Check with. $ fuser -v /dev/snd/*. In general the approach would be to copy the data to all sinks and toggle between them via mute toggling. This can be done in ALSA and PulseAudio. Show $ aplay -l, that PA output is bit verbose. 1. level 2. agentsmurf6.
Pulseaudio device names - OZ9AEC Website
https://oz9aec.net/software/gstreamer/pulseaudio-device-names
The Pulseaudio FAQ has some neat tricks for filtering the device names out: pactl list | grep -A2 'Source #' | grep 'Name: ' | cut -d" " -f2. On my computer this will generate the following list: alsa_output.pci-0000_80_01.0.analog-stereo.monitor alsa_input.pci-0000_80_01.0.analog-stereo. Note the the audio output also appears as a source.
Now you know Pulseaudio No Hardware Output Devices
Now that you know Pulseaudio No Hardware Output Devices, we suggest that you familiarize yourself with information on similar questions.
