We have collected the most relevant information on Ps Audio Resistor Loading. Open the URLs, which are collected below, and you will find all the info you are interested in.
The $35 resistor – PS Audio
https://www.psaudio.com/pauls-posts/the-35-resistor/
Instead of trying to use what everyone else was struggling with: a high-quality potentiometer or fancy stepped attenuator, my simple circuit depended 100% on the quality of a single resistor. After much trial and error, I landed on a 1-watt 0.1% tolerance Vishay that in quantities of 500 pieces ran us $35 each. Ouch.
Cartridge damping – PS Audio
https://www.psaudio.com/pauls-posts/cartridge-damping/
This process is called cartridge loading but more properly cartridge damping. Phono cartridges act like any coil of wire producing a voltage differently per frequency. What we want is a constant output at any frequency so we damp the cartridge with resistors and capacitors. You’re probably familiar with the cartridge loading switches on the ...
Loading Resistors | Zu Audio | Hi-Fi audio speakers and ...
https://www.zuaudio.com/low-voltage/2020/1/24/loading-resistors
Loading Resistors. Loading resistors allow users of higher impedance loudspeakers (32, 16, 12 and 8 ohm) flexibility in making happy (good sounding) amplifier/loudspeaker matchups. Loudspeaker impedance: higher numbers represent an easier, “lighter” load for your amplifier. A loudspeaker’s impedance specification is generally an …
PS Audio – High-End Audio Products
Save up to $400 on your Stellar S300 Stereo Amplifier. Let us purchase your used stereo equipment for the original retail value and apply the amount toward the purchase of a new PS Audio product. Please fill out this form to the best of your knowledge and your card will be charged the lower amount. We’ll send your new PS Audio gear to you ...
What Are The Best Resistors For Audio Equipment? - …
https://www.noisylabs.com/what-are-the-best-resistors-for-audio-equipment/
The best practice for finding the right resistor for your audio equipment is to find a resistor which doubles in power. To find power in a resistor use this formula: P=V squared/R. The P in the equation is power, while the V is for voltage, and the R stands for resistance. Technically, the P which stands for power represents watts.
PS Audio 4.5 Preamplifier Review price specs - Hi-Fi Classic
http://www.hifi-classic.net/review/ps-audio-4-5-143.html
The rated maximum output of the PS Audio Model 4.5 is 18 volts. Driving a standard EIA load of 10,000 ohms in parallel with a 1,000-picofarad (pF) capacitor, it clipped at 15.5 volts. The 1,000-Hz harmonic distortion was very low up to the clipping point, typically reading 0.002 percent or less, and only 0.01 percent at 15 volts.
Fuses – PS Audio
https://www.psaudio.com/pauls-posts/fuses/
Fuses. Change the power fuse in a DAC or preamp and the sound changes, depending on the type of fuse you change to. I first became aware of fuses and their sonic differences in the 1980s. We were working on releasing the 200C power amplifier, designed by Bob Odell. This 200 watt per channel amplifier was the best sounding power amplifier we had ...
Audiogon Discussion Forum
https://forum.audiogon.com/discussions/capacitance-loading-for-at-150-mlx-cart
PS Audio has done a good job here, judging from my noise measurements with a 47K input impedance and the input RCAs open. Very slightly different than the 1K loading choice, which can be easily explained by the increased thermal noise of a 47K resistor vs a 1K resistor.
Need Help Loading a MC Cartridge | Steve Hoffman …
https://forums.stevehoffman.tv/threads/need-help-loading-a-mc-cartridge.313339/
Gneral rule of thumb on loading is 10X internal impedance so I'd load it at 100. Ideal gain is probably around 57 dB so you're right smack dab in the middle of 54 and 60. The cartridge may actually have a higher output than .48 mV (both my 103R's have higher output than spec) so you could try either 54 or 60.
Now you know Ps Audio Resistor Loading
Now that you know Ps Audio Resistor Loading, we suggest that you familiarize yourself with information on similar questions.
