We have collected the most relevant information on Max Receiver Audio Pinout. Open the URLs, which are collected below, and you will find all the info you are interested in.
Balanced Line Receivers - THAT Corporation Audio Technology
http://www.thatcorp.com/datashts/THAT_Line_Receiver_Selection_Guide.pdf
• Balanced audio line receivers • Instrumentation amps • Differential amps 0dB, -3dB, -6dB 0dB, ±3dB, ±6dB 0dB, ±3dB, ±6dB • Two independent channels • High performance • Industry-standard pinout 0dB, ±3dB, ±6dB PSRR (60 or 100 Hz) 80 dB 90 dB 90 dB 90 dB Max Power Supply (Vcc-Vee) 36 Vdc 36 Vdc 36 Vdc 36 Vdc
433 MHz RF Transmitter and Receiver module pinout ...
https://www.etechnophiles.com/433-mhz-rf-transmitter-and-receiver-module-pinout-features-working/
The RF receiver delivers the output to the data pin in an encoded form. The operational voltage range of the module is 5V maximum. The frequency of the receiver can be changed using a node present on it. It is one of the popular and cheapest receivers and has low power consumption. 433MHz RF receiver module uses the ASK signal as an input.
Quad LVDS Line Receivers with Integrated Termination and ...
https://pdfserv.maximintegrated.com/en/ds/MAX9121-MAX9122.pdf
receiver. A fail-safe feature sets the output high when the inputs are open, or when the inputs are undriven and shorted or parallel terminated. The EN and EN inputs con-trol the high-impedance output. The enables are common to all four receivers. Inputs conform to the ANSI TIA/EIA-644 LVDS standard. Flow-through pinout simplifies PC
MAX232CPE Datasheet - RS-232 Drivers/Receivers - Maxim
http://www.datasheetcafe.com/max232cpe-datasheet-rs-232-driver-receiver/
by Pinout. This IC is dual driver/receiver. Part Number : MAX232CPE. Function : +5V-Powered, Multichannel RS-232 Drivers/Receiver. Package : 16 Pin DIP Type. Manufacturers : Maxim Integrated. Image. Description : The MAX220 Thru MAX249 family of line drivers/receivers is intended for all EIA/TIA-232E and V.28/V.24 communications interfaces ...
Motorola MaxTrac, Radius and GM300 Series …
http://www.repeater-builder.com/motorola/maxtrac/maxtrac-intro-stuff.html
If you want de-emphasized receiver audio, you need to pull it from pin 8 on the microphone jack. If you want de-emphasized receiver audio on the 16 pin accessory connector you need to remove the JU 661 bumper block and add a jumper wire internally from the center pin of JU 551 to pin 8 on the microphone jack.
Additional Alinco Information
https://www.repeater-builder.com/alinco/alinco-index-stuff.html
Transmitter audio input. The audio on this pin is not pre-emphasized. Used for 9600 baud packet data. 4: Receiver audio output. The audio on this pin is de-emphasized. Used for 1200 baud packet. 5: Ground. 6: No connection. 7: PTT input, active low. 8 +5vDC out, max current is 50 mA. See comments below. 9: Transmitter audio input. The audio on ...
XDS Pro 4Q AES/EBU Digital Audio Output
http://myxdsreceiver.westwoodone.com/aff/Documentation/XDS_Pro-4Q_AES-EBU_Pinout.pdf
The PRO 4Q receiver has four digital audio output channels that provide AES/EBU versions of the four analog audio output ports A through D. The channels are mapped from analog Port A to the digital pair of CH0 signals, Port B to CH1, Port C to CH2, and Port D to CH3. The following tables contain the interface
KMA 20/KR 21 MARKER BEACON RECEIVER ISOLATION …
https://www.csobeech.com/files/KMA20-Manual.pdf
The marker receiver of the KMA 20, available without the isolation amplifier and audio panel is the KR 21. The receiver is a crystal controlled superheterodyne receiver and has excellent selectivity and freedom from interference of television and FM stations. Operating controls for the marker receiver consists of two toggle switches on the KMA
KMA 24 and KMA 24H - heilmannpub.com
http://heilmannpub.com/KMA24.pdf
To listen to a specific receiver, simply press the corresponding headphone or speaker button “in.” To disconnect that receiver, press the button again. It will return to the “out” position. For both the KMA 24 and KMA 24H, volume of audio input from transceivers and receivers is set with the volume controls of each individual radio.
Now you know Max Receiver Audio Pinout
Now that you know Max Receiver Audio Pinout, we suggest that you familiarize yourself with information on similar questions.
