We have collected the most relevant information on Kde Audio Devices Not Enabled In Config. Open the URLs, which are collected below, and you will find all the info you are interested in.
Sound Problems - KDE UserBase Wiki
https://userbase.kde.org/Sound_Problems#:~:text=KDE%204%20uses%20the%20wrong%20sound%20device.%20That,and%20go%20to%20Multimedia%20in%20the%20General%20tab.
Audio configuration problems • KDE Community Forums
https://forum.kde.org/viewtopic.php?t=117976
Check the Audio Hardware Setup tab to change it if needed. Running Kubuntu 21.10 with Plasma 5.23.5, Frameworks 5.89.0, Qt 5.15.2, kernel 5.13.0-23 on Ryzen 5 4600H, AMD Renoir, X11. FWIW: it is always useful to state the exact …
Sound Problems - KDE UserBase Wiki
https://userbase.kde.org/Sound_Problems
KDE 4 uses the wrong sound device. That is not an error, but a configuration issue. To tell KDE 4 which soundcard to use (or prefer if available), open System Settings and go to Multimedia in the General tab. Devices from /etc/asound.conf or ~/.asoundrc are not listed. Phonon uses a function introduced in ALSA 1.0.14 to find those devices. To make this function list your entry you need …
No audio devices (clean install Manjaro KDE 20.1): Model ...
https://forum.manjaro.org/t/no-audio-devices-clean-install-manjaro-kde-20-1-model-intel-comet-lake-pch-cavs/24389
The audio doesn’t work because the system can’t use my sound card. This has happened since installation. The sound works in Windows, just not here. I’ve also tried with headphones and bluetooth, with the same issue. I’ve looked into some solutions online, but I haven’t found the exact same issue/audio card, so I didn’t try to blindly install strange drivers or …
sound - KDE 5 - How to easily switch between audio …
https://askubuntu.com/questions/756390/kde-5-how-to-easily-switch-between-audio-outputs
Restart pulse audio with this command: pulseaudio --kill; sleep 1; pulseaudio --start 4. Go to KDE phonon settings > Audio Hardware setup and select the new profile. Now you should see both profile in the mixed and so you'll be able to switch easy: I would suggest to use this plasmoid mixer: https://store.kde.org/p/1100894/
How to enable both built-in audio output and HDMI audio ...
https://unix.stackexchange.com/questions/143865/how-to-enable-both-built-in-audio-output-and-hdmi-audio-output-with-pulseaudio
Unfortunately, load-module module-alsa-sink device=hw:0,3 did not work to add HDMI output to Pulse's "Analog Stereo Duplex" configuration. Pulse would start, but no HDMI output. I compared the output of pacmd list-sinks in the two situations. When I added device=hw:0,3, that one would show up without ports. When HDMI output was chosen in ...
Sound troubleshooting - openSUSE Wiki
https://en.opensuse.org/Sound_troubleshooting
If you can see sound devices and change volume, but speaker or headphone don't have output, you might need to configure your sound devices. Configure sound devices in KDE. In KDE, open System Settings > Multimedia > Sound & Volume. In Devices tab, you can find all sound devices that are being used. When you have multiple sound cards, make sure your first choice is set as …
Kdenlive/Manual/Settings Menu/Configure Kdenlive - KDE ...
https://userbase.kde.org/Kdenlive/Manual/Settings_Menu/Configure_Kdenlive
Configure the Video and Audio drivers and devices. For advanced users only. In version 0.9.4 of Kdenlive, checking the "use Open GL for video playback" checkbox turns on the ability to have audio scrubbing available for use in the clips. Audio scrubbing lets you hear the audio at the playhead position as you drag the playhead so you can quickly find a particular sound or event …
KDE - ArchWiki - Arch Linux
https://wiki.archlinux.org/title/KDE
Try to remove qt5ct and kvantum related package then apply default global plasma theme. if the problem persists, try clear all your kde config and reinstall overwrite plasma package. Be sure to check hidpi scaling in KDE system settings as well. Fonts Fonts in a Plasma session look poor. Try installing the ttf-dejavu and ttf-liberation packages.
LinuxQuestions.org - [SOLVED] No Sound with Realtek ALC892 ...
https://www.linuxquestions.org/questions/linux-desktop-74/no-sound-with-realtek-alc892-on-debian-squeeze-826982-print/
Config options: 0 Installed drivers: Type 10: ALSA emulation Card config: HDA ATI SB at 0xfe5f8000 irq 16 HDA ATI HDMI at 0xfe6ec000 irq 47 Audio devices: 0: ALC892 Analog (DUPLEX) Synth devices: NOT ENABLED IN CONFIG Midi devices: NOT ENABLED IN CONFIG Timers: 31: system timer Mixers: 0: Realtek ALC892 1: ATI R6xx HDMI
Now you know Kde Audio Devices Not Enabled In Config
Now that you know Kde Audio Devices Not Enabled In Config, we suggest that you familiarize yourself with information on similar questions.
