We have collected the most relevant information on Hdmi_Force_Edid_Audio=1 Xbian. Open the URLs, which are collected below, and you will find all the info you are interested in.
No audio on Xbian connected to an AV receiver via HDMI ...
https://raspberrypi.stackexchange.com/questions/14764/no-audio-on-xbian-connected-to-an-av-receiver-via-hdmi
hdmi_force_hotplug=1 hdmi_drive=2 And even tried forcing EDID Audio: # HDMI Force EDID Audio # Pretends all audio formats are supported by display, allowing passthrough of # DTS/AC3 even when not reported as supported. hdmi_force_edid_audio=1 But with no success. One more thing. The AV Receiver (Sony SDR-K890 with a 6.1 surround system) has two ...
RPi Configuration - eLinux.org
https://elinux.org/RPi_Configuration
hdmi_ignore_edid=0xa5000080 hdmi_force_edid_audio Pretends all audio formats are supported by display, allowing passthrough of DTS/AC3 even when not reported as supported. hdmi_force_edid_audio=1 hdmi_ignore_cec Pretends CEC is not supported by TV. Avoids bringing (CEC enabled) TV out of standby and channel switch when rebooting.
kernel modules - How to force HDMI audio (intel card) to ...
https://unix.stackexchange.com/questions/391326/how-to-force-hdmi-audio-intel-card-to-be-enabled-despite-receiving-broken-edid
However, the HDMI audio doesn't work. Pulseaudio is set to the correct sink, which is detected as unplugged (not-available). I tried the following without any resulting change: Add the edid file in initramfs so that EDID is loaded earlier; xrandr --output HDMI-1 --set audio on
7inch HDMI Display (H) - LCD wiki
http://www.lcdwiki.com/7inch_HDMI_Display_(H)
hdmi_force_edid_audio=1 max_usb_current=1 hdmi_force_hotplug=1 config_hdmi_boost=7 hdmi_group=2 hdmi_mode=87 hdmi_drive=2 display_rotate=0 hdmi_cvt 1024 600 60 6 0 0 0 Step 4. Insert SD card. After the above steps are completed, pop up the SD card on the computer and insert it into the SD card slot on the back of the raspberry pie. ...
What is HDMI EDID? Everything You Need to Know!
https://thehometheaterdiy.com/hdmi-edid/
My question relates to EDID as it concerns audio specs. I was hoping to extract audio from an HDMI output from a receiver (between the receiver and the monitor). The HDMI extractor will accept Linear PCM 5.1 or 7.1 but does not decode DTS or AC3. it would seem that I should be able to use a device like this to inform the receiver that this ...
Force HDMI to carry 5.1 Dolby or whatever - Windows 10 ...
https://www.tenforums.com/sound-audio/148247-force-hdmi-carry-5-1-dolby-whatever.html
The Nvidia card has a display port to HDMI adapter, which I use to connect to the HDMI audio extractor which sends the HDMI on to the HDTV. But all the sound it ever gets is stereo. I plug a fireTV stick into the HDMI splitter and I get 5.1 Dolby out of the sound coaxial port on both the splitter and the HDTV, so the hardware works.
Forcing 5.1 audio to TV via HDMI | NVIDIA GeForce Forums
https://www.nvidia.com/en-us/geforce/forums/geforce-graphics-cards/5/122325/forcing-51-audio-to-tv-via-hdmi/
When you attach an HDMI cable from any modern GeForce card to a modern TV set, the Nvidia drivers detect that the TV only supports stereo even if the TV is attached to an external 5.1 surround sound system. Therefore, it becomes impossible to transfer 5.1 audio from the video card through to the TV via HDMI, and you end up getting stuck with ...
HDMI-CEC stops working when other HDMI device is powered ...
https://forums.raspberrypi.com/viewtopic.php?t=86150
I don't know where to ask this question (XBian, XBMC, libCEC forums?), so I'll start here. I have Raspberry Pi model B+ with XBian installed and it's connected to HDMI port in Pan
DTS passtrough audio dropouts (openelec/raspbmc/xbian)
https://forum.kodi.tv/showthread.php?tid=174776
- all builds/versions I could find inlucding rbej's testbuilds, nightlys, xbian/rasp/openelec - editing the config.txt with different values for HDMI, f.x hdmi_force_edid_audio=1 etc. (But perhaps not all combinations there is..) - new power supplies, new HDMI cables - debug log in xbmc shows nothing when the dropouts happens
Now you know Hdmi_Force_Edid_Audio=1 Xbian
Now that you know Hdmi_Force_Edid_Audio=1 Xbian, we suggest that you familiarize yourself with information on similar questions.
