We have collected the most relevant information on Ft-950 Audio Setup. Open the URLs, which are collected below, and you will find all the info you are interested in.
WB Audio Section: K6JRF 10/7/2008
https://www.k6jrf.com/FT2k_No_EQ.html#:~:text=W6GEV%3A%20FT-950%20w%2F%20%22MD100%22%20mic%20plugged%20directly%20into,to%20%22wide%22%20for%20rag-chew%20and%20%22narrow%22%20for%20DX.
N2RIT ESSB Audio Equipment
http://www.n2rit.com/audio/audio.html
audio. My audio setup is built around a YAESU FT-950 Microphone EQ Setting MIC2200 - PREAMP: The least expensive microphone preamp of quality that you can buy. The preamp has other features such as parametric EQ etc. I started …
FT-950 Unboxing, Setup, And More! - YouTube
https://www.youtube.com/watch?v=wZCXv9ihQzg
The 950 arrived today! Here is a video showing the unboxing and more. Bob (K7RNV) got the honors of first QSO! Thanks for the great report Bob!
FT-950 CAT MANUAL - Yaesu
https://www.yaesu.com/downloadFile.cfm?FileID=2928&FileCatID=158&FileName=FT%2D950%5FCAT%5FManual%5FENG.pdf&FileContentType=application%2Fpdf
There is three for the FT-950 Command as shown below: Set command: Set a particular condition (to the FT-950) Read command: Reads an answer (from the FT-950) Answer command: Transmits a condition (from the FT-950) For example, note the following in the case of the FA com-mand (Set the VFO-A frequency): To set the VFO-A frequency to 14.250000 MHz, the
Yaesu FT-950 Tips - ve3ips
https://ve3ips.wordpress.com/2016/08/12/yaesu-ft-950-tips/
Audio Peaking Filter or APF. This feature actually enhances the sound of CW by providing a very narrow audio bandwidth, in many cases enhancing the sound of the CW. There are no adjustments for the APF. You either turn it on or turn it off. To active the APF feature you push the CONT button for a few seconds. Roofing Filter – R.FIL
Adjusting Your Rig’s DSP Settings - Heil Amateur Radio
https://heilhamradio.com/support/dsp-settings/adjusting-your-rigs-dsp-settings/
DSP Setting Example: Yaesu FT-950/2000 and FTdx9000 Series. These rigs use a three-band parametric equalizer system. In each of the audio “bands” (low, mid, and high-frequency areas), you can set the center frequency, amplitude, and bandwidth of equalization. Generally, the modulators of these rigs want you to roll off bass and enhance treble.
Yaesu ft950 with studio mic - Transmission1
https://www.transmission1.net/viewtopic.php?t=46981
Try theses settings for audio on the FT950: TX Audio Group Settings: 091 = 200 092 = -15 093 = 5 094 = 700 095 = -6 096 = 5 097 = 2400 098 = 8 099 = 5 100 = 700 101 = -16 102 = 1 103 = 1100 104 = -1 105 = 1 106 = 2100 107 = 0 108 = 1 109 = 50 Additionally set the SSB bandwidth menu 64 to (200Hz to 2800Hz). I don't think you'll be disappointed.
Software Settings - VK4SN Amateur Radio Station
https://www.vk4sn.com/Technical/Settings
Set up the Remote station first. THE SLAVE/REMOTE COMPUTER. Set up the radio. On the Menu Bar, click on Parameters - Setup; Click on the TRX1 Tab Select your Radio; Select your comm port; Select your CAT Speed; Select RTS/DTR as appropriate to your radio; Click OK; Set up the communications
WB Audio Section: K6JRF 10/7/2008
https://www.k6jrf.com/FT2k_No_EQ.html
The settings here reflect the latest FT950 FW update W6GEV: FT-950 w/ "MD100" mic plugged directly into the radio MD100 settings: "Lo Cut 1" from 150hz to 1000hz is recommended along w/ "Hi-Emphasis". WV6N always uses the "PROC" and it's set to "30". The Tx BW is NOT changed; always on 1-30.
Audio Profiles
https://www.3895khz.com/_mgxroot/page_10768.html
1) Turn off the 9000 via front panel switch. 2) Hold the "AFL" and "ACM" buttons in while turning the power on. 3) Under menu "No. 070", the TTBF should now be ON. You're done! 4) To reverse the process, just repeat the process.
Transmitter Bandwidth Settings for eSSB
https://www.nu9n.com/transmitter_settings.html
Yaesu FT-9000 TTBF Settings for eSSB: (4kHz BW) 1) Turn off the 9000 via front panel switch. 2) Hold the "AFL" and "ACM" buttons in while turning the power on. 3) Under menu "No. 070", the TTBF should now be ON. You're done! 4) To reverse the process, just repeat the process. EQ Settings: Menu 69 select Front or Rear mic input #1 Parametric ...
Now you know Ft-950 Audio Setup
Now that you know Ft-950 Audio Setup, we suggest that you familiarize yourself with information on similar questions.
