We have collected the most relevant information on Elecraft K3 Transmit Audio. Open the URLs, which are collected below, and you will find all the info you are interested in.
[Elecraft] Help! K3 God-awful transmit audio
https://elecraft.mailman.qth.narkive.com/8jsS5otZ/help-k3-god-awful-transmit-audio
The audio indeed could be classified as "muffled". Furthermore, it also sounded distorted, as thought the microphone gain was set too high. Oddly, it was distorted independently of the gain setting. I have not had a voice QSO on the K3 since that moment. The K3 transmit audio, at least on 40 meter LSB, was horrid. I would not be overly
K3 Enhancements and Mods and Tech Alerts – Elecraft
https://elecraft.com/pages/k3-enhancements-and-mods-and-tech-alerts
Some K3 owners have noted distorted transmit audio caused by RF energy being coupled into the front-panel microphone input. In most cases this has been corrected by bypassing an RF choke in the K3 microphone circuit as described in this application note. Revision A November 12, 2008
K3S Transceiver – Elecraft
https://elecraft.com/products/k3s-transceiver
The KBPF3A option extends receive coverage down to 100 kHz, covers all SWL bands, and allows 0.5 mW transmit output on the 472 kHz (630 m) band for use with external amplifiers. The K3S is the only deluxe transceiver that is targeted at both home and field use.
Elecraft K3 Settings – K5ZD
https://k5zd.com/elecraft-k3-settings/
Bob, N6TV, recommends the following K3 settings: First set CONFIG:TECH MD ON to un-hide some AGC settings. Set TECH MD OFF when finished, to eliminate useless options from appearing in the SubRx display choices (PLL1, AFV, dBV, etc.) AF GAIN LO — Cuts audio hiss. May not work with all headphones.
[Elecraft] [K3] transmit equalizer settings
https://elecraft.mailman.qth.narkive.com/nx3pQb7i/k3-transmit-equalizer-settings
To: elecraft at mailman.qth.net. Subject: Re: [Elecraft] [K3] transmit equalizer settings. <<<If there is enough macro memory, it will work.>>>. Well there isn't, the limit on a Macro is 120 characters. The problem is, you can't just set an EQ band with a single command. You need to step UP or.
SignaLink USB SLUSBK3 FOR ELECRAFT K3 & K3/S REAR PORTS ...
https://shop.thehamshop.com/slusbk3
The SignaLink USB p/n SLUSBK3 is compatible with Elecraft K3 & K3/S radios. ... Transmit Audio / "Side Tone" Output - A rear panel "Monitor" jack can be used with headphones or powered (amplified) speakers to monitor your Transmit Audio, or Side Tone during CW operation.
ELECRAFT K3 QUICK-START GUIDE - kkn.net
https://www.kkn.net/~tree/K3/K3%20quick%20start8.pdf
• The TX LED {4} indicates that the K3 is in transmit mode. The ∆f LED turns on if the RX and TX frequencies are unequal (SPLIT, RIT/XIT, cross-mode, etc.). (Pg. ??.) • XMIT {8} is equivalent to PTT {35}. Hold TUNE to put out full CW power. • Tap ATU TUNE {8} to auto-tune (KAT3). Hold ATU to select normal/bypass ATU mode.
Now you know Elecraft K3 Transmit Audio
Now that you know Elecraft K3 Transmit Audio, we suggest that you familiarize yourself with information on similar questions.
