We have collected the most relevant information on Dragon Audio Quality Check Failed. Open the URLs, which are collected below, and you will find all the info you are interested in.
Troubleshooting audio and recognition - Nuance
https://www.nuance.com/products/help/dragon/dragon-for-mac/enx/Content/Troubleshooting/TroubleshootingAudio.htm
The audio quality of the built-in Bluetooth receiver is too low. Be aware that older devices, such as analog devices with two 1/8 inch jacks, are likely to cause more audio problems than an internal or USB device. No audio signal. If Dragon is …
If audio quality is low - Nuance Communications
https://www.nuance.com/products/help/dragon15/dragon-for-pc/enx/dmpe_sub/Content/DialogBoxes/problems/recognition_deteriorates.htm
If Dragon detects an issue with low-quality audio, one of the following audio quality warnings appears: Low-quality audio/Poor signal: Appears when you are working in a very noisy environment or if there is a problem with... Bluetooth dropouts: Appears when your Bluetooth microphone battery is low ...
Checking Your Audio Settings in Dragon - ProCAT
https://www.procat.com/Winner/tips/CheckAudioSettings.htm
Click “Start Quality Check” make sure that you speak in your “Court Voice”. If sound quality is poor, Dragon will let you know. If you fail the audio check, sound quality issues, will need to be addressed before you continue. If there are no audio issues click Finish.
Fixing Dragon (and VoiceComputer) in 6 Steps - …
https://voicecomputer.com/fixing-dragon/
Beginning with Dragon 13 through Dragon 15, the Audio Setup Wizard has been simplified and no longer contains the Volume Check or Quality Check screens. It also no longer contains a playback off. If you need assistance with running the audio setup wizard in Dragon 12 and below, contact us at [email protected] or post a request for help on the VoiceComputer forum.
Unable to complete the Audio Setup Wizard (Microphone Check)
http://nuance.custhelp.com/app/answers/detail/a_id/4353/~/unable-to-complete-the-audio-setup-wizard-%28microphone-check%29
Close out of the Sound Recorder and run the Audio Setup Wizard in Dragon again. Windows Vista: Click on "Start > Control Panel". On the left, select "Classic View" if not already selected. Choose "Sound". Switch to the "Recording Tab" and verify that the microphone is working. Notes:
"The speech engine returned the following error ...
http://nuance.custhelp.com/app/answers/detail/a_id/6753/~/the-speech-engine-returned-the-following-error%3A-dsxwarning_uttspurged-warning
Use the troubleshooting listed in TN 3231: Microphone Troubleshooting. Check the microphone in Dragon NaturallySpeaking by going to "Audio > Check microphone..." Use the troubleshooting listed in TN 4720: Unable to complete the …
KnowBrainer Speech Recognition Forums - DNS 11 "The sound ...
https://knowbrainer.com/forums/forum/messageview.cfm?catid=4&threadid=11269
This is what generally produces the audio quality check failure. On the other hand, if the blue bar moves all the way to the bottom so that the volume adjustment bar is all black, then your microphone by them is too loud (i.e., the microphone gain is too high) and this can tend to cause an audio quality check failure as well.
KnowBrainer Speech Recognition Forums - Dragon 15.3 ...
https://www.knowbrainer.com/forums/forum/messageview.cfm?catid=4&threadid=31591
A couple of small corrections. The DNS abbreviation for Dragon NaturallySpeaking hasn't been used since Ver. 13 (when it was retired). You are probably using DPI 15.3 (Dragon Professional Individual). Try substituting DPI 15.3 so that we have the right information. You are not using Ver. 5.3. You're using 15.3.
Speech Recognition Troubleshooting Tutorials
https://www.speechrecsolutions.com/tutorials.html
This is the process of asking Dragon to reset the input volume of you speech and to confirm overall audio quality. You can launch the audio set-up wizard either by saying "check audio" or navigating to Tools > Accuracy Center > Check Audio Settings. The very act of running the audio set-up wizard will often solve issues. In addition, after the second phase of the process (the …
Microphone Set-up and Troubleshooting Guide Dragon …
https://www.speechrecsolutions.com/assets/Microphone_Setup_Troubleshooting_Guide2.pdf
gain and also provides a crude check of your system integrity by means of providing a speech to noise ratio. The audio set-up wizard can be access either by saying “check audio” or manually by going to Tools > Accuracy Center > Check My Audio Settings. As long as you get a speech to noise ration between 15 and 25, your system is probably OK.
Now you know Dragon Audio Quality Check Failed
Now that you know Dragon Audio Quality Check Failed, we suggest that you familiarize yourself with information on similar questions.
