We have collected the most relevant information on Cisco Ip Communicator No Audio. Open the URLs, which are collected below, and you will find all the info you are interested in.
IP Communicator - No Audio on Occasion - Cisco Community
https://community.cisco.com/t5/ip-telephony-and-phones/ip-communicator-no-audio-on-occasion/td-p/2096488#:~:text=When%20one%20individual%20calls%20another%2C%20the%20call%20is,the%20person%27s%20extension%20number%20at%20the%20voice%20prompt.
No sound output with IP Communicator - Cisco Community
https://community.cisco.com/t5/ip-telephony-and-phones/no-sound-output-with-ip-communicator/td-p/1851752
If yes, ensure you are selecting the interface which you get after connecting over VPN & not the default NIC. This is usually the main cause of one-way audio. Also, ensure CIPC installation on Win 7 is supported, mostly it is but double chk to be sure. If it helps, pls rate the post. GP 5 Helpful Reply galaxy573 Beginner
No audio on voice calls over VPN ... - Cisco Community
https://community.cisco.com/t5/ip-telephony-and-phones/no-audio-on-voice-calls-over-vpn-softphone-to-from-remote-site/td-p/2224430
We then see the IP Communicator start receiving RTP from 10.23.32.50 to port 24582 as expected. Your IP Communicator never starts sending audio back to 10.23.32.50. Most likely, this means you are not advertising all the routes in your VPN setup. Are you using split tunneling? Can you ping the 10.23.32.50 address from your PC running AnyConnect?
Cisco Bug: CSCsa65866 - Communicator-'No Compatible Sound ...
https://quickview.cloudapps.cisco.com/quickview/bug/CSCsa65866
Symptom: IP Communicator Audio Tuning Wizard shows nothing in the dropdown selection boxes, and when Communicator is launched, it gives a messages stating: "There are no compatible sound devices installed on this computer."Conditions: Attempting to install/use IP Communicator on a system that has different names for the Playback (wave out) and …
Solved: Cisco IP Communicator - No Devices Detected ...
https://community.cisco.com/t5/ip-telephony-and-phones/cisco-ip-communicator-no-devices-detected/td-p/2073804
It will allow you to click on "cancel" when IP Comm says the "default" device is not found and start the audio wizard and then your device will be listed there. For instance, using this method allows you to use headsets, integrated speakers/mic on a laptop, or whatever you like. Regards 5 Helpful Reply moman62 Beginner
Troubleshooting Cisco IP Communicator
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cipc/7_0/english/user/guide/CIPCUG70/ipcugts.pdf
Cisco IP Communicator or with the remote phone by calling additional parties. If you suspect that the problem lies with the other phone, adjust the volume on Cisco IP Communicator, but avoid modifying settings through the Audio Tuning Wizard because these modifications might not be broadly applicable.
No Audio Cisco IP Communicator ver 8.6.6.0 : Cisco
https://www.reddit.com/r/Cisco/comments/nq39pj/no_audio_cisco_ip_communicator_ver_8660/
No Audio Cisco IP Communicator ver 8.6.6.0. Question. Hello, I am using Cisco IP Communicator ver 8.6.6.0 and can get dial tone, the phone rings and connects, but I cannot hear the other person and the other person cannot hear me. I am using in conjunction with a FortiClient VPN.
Troubleshooting Cisco IP Communicator
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cipc/1_1/english/administration/guide/admin/CADoip.pdf
† The Cisco IP Communicator audio settings are incorrect. See the Cisco IP Communicator User Guide for more information. If the Cisco IP Communicator party cannot hear the remote party, it may be for the following reasons: † The Cisco IP Communicator user is relying on a non-supported VPN. To
Using Headsets and Other Audio Devices with Cisco IP ...
https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cipc/7_0/english/user/guide/CIPCUG70/ipcugdev.pdf
Cisco IP Communicator uses speakerphone mode as the default audio mode. Cisco IP Communicator responds to softkeys, speed-dial buttons, and other features by routing audio through the active mode. You can use a headset with all of the controls on Cisco IP Communicator, including the Volume button and the Mute button.
Now you know Cisco Ip Communicator No Audio
Now that you know Cisco Ip Communicator No Audio, we suggest that you familiarize yourself with information on similar questions.
