We have collected the most relevant information on Best Resistor For Audio Use. Open the URLs, which are collected below, and you will find all the info you are interested in.
What Are The Best Resistors For Audio Equipment ...
https://www.noisylabs.com/what-are-the-best-resistors-for-audio-equipment/
Foil resistors on one hand is better for low audio equipment application while carbon composition is better at storing higher wattage because of its thermal dynamics. So if you were wanting to find a resistor for a small radio, you would go with a foil resistor. But there are other specifications which will help you with your decision.
What is the BEST resistor for audio use - High-End Audio ...
https://forum.audiogon.com/discussions/what-is-the-best-resistor-for-audio-use
I tend to prefer Kiwami resistors in tubed applications, as Vishays can sound a little too analytical. However, from what I've heard, the Vishay/Dales are the finest sounding resistors for the Goldpoint stepped attenuators. Very, very clean sounding response...exactly what you want in a pre. Cheers! dismalonyx OP 36 posts 11-19-2001 7:07pm
Best SMD resistors for AUDIO. | diyAudio
https://www.diyaudio.com/community/threads/best-smd-resistors-for-audio.340561/
EETimes - Selecting resistors for preamp, amplifier and ...
https://www.eetimes.com/selecting-resistors-for-preamp-amplifier-and-other-high-end-audio-applications/
The Bulk Metal foil resistor is the preferable choice for audio amplifiers when high linearity of amplification and minimal dynamic distortion are required. In particular, Vishay Precision Group recommends the VAR, Z201, S102C, Z203, VSHZ, VSMP Series (0603-2018), VFCP Series, SMRXDZ Series resistors for noise-free performance in audio applications ( …
Resistor Article for Audio | What's Best Audio and Video ...
https://www.whatsbestforum.com/threads/resistor-article-for-audio.1790/
The Vishay Z-foil resistors are some of the best sounding resistors on the planet. Unfortunately, they are incredibly difficult to find retail, and some of the more expensive ones can cost $25 each in 1,000 minimums. Nevertheless, they are not a silver bullet.
Choosing the Right Resistor for Your Amplifier Project ...
http://mojoshout.com/uncategorized/choosing-the-right-resistor-for-your-amplifier-project/
Wire-wound resistors are the least noisy followed by metal-film, metal-oxide, and carbon-film. The noisiest— carbon comp. So, if you are concerned with noise, use metal-film resistors, especially in the input stage. Aiken Amps has a great article that goes into detail about the different types of noise that a resistor can produce.
Resistors: Types And Applications - Nuts and Volts …
https://www.nutsvolts.com/magazine/article/resistors_types_and_applications
There are special versions with windings that cancel most of the inductance, but have a much higher C P that also affects the resistor’s performance above 50 kHz. Ceramic and Metal Oxide. If you need a high-power non-inductive resistor, you can use cermet (ceramic-metal mix) or metal oxide resistors.
The best sounding I/V resistor - diyAudio
https://www.diyaudio.com/archive/blogs/dvb-projekt/969-best-sounding-i-v-resistor.html
Hey, thanks for the tip. The GG102A is truly amazing. Better than the previous S102K resistor. While the sound from S102K is already airy and clear, but the GG102A adds more depth (3D) and fluid. It's hard to believe a wirewound resistor will have such enhancement.
Best transistor to use for audio amplifier - Electrical ...
https://electronics.stackexchange.com/questions/97827/best-transistor-to-use-for-audio-amplifier
If you are aiming for a few Watts, I'd probably go with basic parts like the TIP41 (NPN) and TIP42 (PNP). Again though, it's not the choice of transistor that will make or break this project. You can certainly create a impressive audio amp with the transistors I mention, but you can also make a mess.
Best resistor type for speaker crossover | Headphone ...
https://www.head-fi.org/threads/best-resistor-type-for-speaker-crossover.566217/
If i was going to design my own crossover i'd try to use metal oxide, so i don't have to worry about the inductance in the design. You can get 5W and 10W metal oxide resistors pretty easily, a single resistor rated to do the job is a better option than multiple smaller ones. i have the energy of a bear, that has the energy of two bears.
Now you know Best Resistor For Audio Use
Now that you know Best Resistor For Audio Use, we suggest that you familiarize yourself with information on similar questions.
