We have collected the most relevant information on Balanced Audio Line Driver Ic. Open the URLs, which are collected below, and you will find all the info you are interested in.


Balanced Line Driver ICs - THAT Corporation Audio Technology

    http://www.thatcorp.com/1600-series_Balanced_Line_Driver_ICs.shtml
    THAT Corporation 1606/1646 OutSmarts Balanced Line Driver ICs. The THAT 1606 and 1646 are a new generation of monolithic differential line drivers offering improved performance over conventional cross-coupled designs. Based on a high-performance, fully differential op amp and laser-trimmed thin-film resistors, both exhibit low noise and distortion, high slew rate, and wide …

Balanced Line Driver SSM2142 - Analog Devices

    https://www.analog.com/media/en/technical-documentation/data-sheets/SSM2142.pdf
    a Balanced Line Driver SSM2142 FEATURES Transformer-Like Balanced Output Drives 10 V RMS Into a 600 V Load Stable When Driving Large Capacitive Loads and Long Cables Low Distortion 0.006% typ 20 Hz–20 kHz, 10 V RMS into 600 V High Slew Rate 15 V/ms typ Low Gain Error (Differential or Single-Ended); 0.7% typ Outputs Short-Circuit Protected

Balanced Audio Line Driver (Unbalance to Balance Audio ...

    https://www.twovolt.com/2019/01/19/audio-balanced-line-driver-unbalance-to-balance-audio-signal-converter-using-drv135-ssm2142/
    Balanced Audio Line Driver (Unbalance to Balance Audio Signal Converter) Using DRV135/SSM2142. The Mini board converts unbalance Audio signal into balance audio signal, the project is based on SSM2142 or DRV135 IC which are differential output amplifier that converts a single ended audio signal input to a balanced output pair.

THAT Corporation Balanced Line Driver ICs

    http://thatcorp.com/datashts/1600data.pdf
    Balanced Line Driver ICs FEATURES • Balanced, transformer-like floating output † OutSmarts® technology improves clipping into single-ended loads † Stable driving long cables and capacitive loads † High output: 18Vrms into 600 † Low noise: -101 dBu † Low distortion: 0.0007% @ 1kHz † Industry-standard pinout APPLICATIONS

Getting the Most from THAT’s Balanced Line Drivers and ...

    https://audioxpress.com/article/getting-the-most-from-that-s-balanced-line-drivers-and-receivers
    Balanced Line Driver THAT’s 1646 Balanced Line Driver is a very simple IC to implement, requiring very few external components. A complete schematic, including RFI protection and power supply bypassing, is shown in Fig. 6. A stereo pair will fit on the D4 prototyping board with room to spare; IC sockets are optional.

DRV13x Audio-Balanced Line Drivers - Texas …

    https://www.ti.com/lit/ds/symlink/drv134.pdf
    DRV13x Audio-Balanced Line Drivers 1 Features 3 Description The DRV134 and DRV135 are differential output 1• Balanced Output amplifiers that convert asingle-ended input to • Low Distortion: 0.0005% at f = 1 kHz balanced output pair. These balanced audio drivers • Wide Output Swing: 17Vrms into 600 Ω consist of high performance op amps with on-chip

Audio line driver - Electronic Circuits and Diagrams ...

    https://www.circuitstoday.com/audio-line-driver
    Description. This is the circuit diagram of a two channel audio line driver using the high performance dual opamp IC TSH22 from ST Microelectronics. The 25 MHz bandwidth, low distortion and high output current of the IC makes it possible to drive medium impedance loads at a high level of modulation. Here both of the opamps inside the IC are wired as non inverting …

DRV135 data sheet, product information and support | …

    https://www.ti.com/product/DRV135
    These balanced audio drivers consist of high performance op amps with on-chip precision resistors. They are fully specified for high performance audio applications and have excellent ac specifications, including low distortion (0.0005% at 1 kHz) and high slew rate (15 V/µs).

Design of High-Performance Balanced Audio Interfaces

    https://www.jhbrandt.net/wp-content/uploads/2014/11/Design_of_High-Performance_Balanced_Audio_Interfaces.pdf
    The purpose of a balanced audio interface is to efficiently transfer signal voltage from driver to receiver while rejecting ground noise. Used with suitable cables, the interface can also reject interference caused by external electric and magnetic fields acting on the cable. The true nature of balanced interfaces is widely misunderstood.

NCS2632 - NOCAP, Pop-Free, 3 Vrms Audio Line …

    https://www.onsemi.com/pdf/datasheet/ncs2632-d.pdf
    Audio Line Driver with Adjustable Gain The NCS2632 is a pop−free stereo line driver. It uses ON Semiconductor’s patented NOCAP technology which allows the elimination of the external DC−blocking capacitors by providing ground−referenced outputs through the generation of an internal negative supply rail.

Now you know Balanced Audio Line Driver Ic

Now that you know Balanced Audio Line Driver Ic, we suggest that you familiarize yourself with information on similar questions.