We have collected the most relevant information on Audiocodes Sip Parameters. Open the URLs, which are collected below, and you will find all the info you are interested in.
AudioCodes 4.6 FXO Gateway - Manual Config - sipXecs ...
https://sipfoundry.atlassian.net/wiki/spaces/sipXecs/pages/492006/AudioCodes+4.6+FXO+Gateway+-+Manual+Config#:~:text=SIP%20Parameters%20Gateway%20Name%3A%20The%20name%20of%20the,required%20to%20work%20with%20sipX%20as%20the%20proxy.
SIP Message Syntax - AudioCodes
https://www.audiocodes.com/media/13527/sip-message-manipulation-syntax-reference-guide-ver-72.pdf
Reference Guide AudioCodes Media Gateway, Session Border Controller and MSBR Series SIP Message Syntax Message Manipulation Message Conditions
SIP Message Manipulation, Conditions and Call …
https://www.audiocodes.com/media/13395/sip-message-manipulation-reference-guide-ver-72.pdf
Reference Guide AudioCodes Media Gateways, Session Border Controllers & MSBRs SIP Message Manipulation, Conditions and Call Setup Rules Version 7.2
AudioCodes Mediant 1000 Configuration - Altigen
https://know.altigen.com/attachments/1266/AudioCodes-Mediant1000.pdf
Set SIP General Parameters Configure the gateway SIP parameters. 1. Select VoIP > SIP Definitions > General Parameters. 2. Set the following parameters: • Set Enable Early Media to Enable • Set Session Expires Time to 300 • Make sure that SIP Transport Type is set to UDP • Make sure that SIP TLS Local Port is set to 5061 3. Click Submit.
AudioCodes Quick Reference Guide – Transcoding
https://www.audiocodes.com/media/13566/audiocodes-quick-reference-guide-transcoding.pdf
In the IP Profiles Table, configure the IP Profile for the IP Group of the sip entity that you want to extend coders for. a. Assign the Coders Group to the IP Profile using the 'Extension Coders Group' parameter under the SBC Media section. b. Enable extension coders by configuring the 'Allowed Coders Mode' parameter to
AudioCodes 4.6 FXO Gateway - Manual Config - sipXecs ...
https://sipfoundry.atlassian.net/wiki/spaces/sipXecs/pages/492006/AudioCodes+4.6+FXO+Gateway+-+Manual+Config
SIP Parameters. Gateway Name: The name of the AudioCodes gateway (has to be in DNS) or IP address. Working with Proxy: Yes, required to work with sipX as the proxy. Proxy IP address: IP address of sipX. Proxy Name: We assume that you are using DNS SRV for your sipX installation and that there is a DNS SRV resource record that points at the sipX server.
MP-11x and MP-124 SIP User's Manual Ver. 6 - …
https://www.audiocodes.com/media/13280/mp-11x-and-mp-124-sip-users-manual-ver-66.pdf
User's Manual AudioCodes Analog Media Gateways MediaPack™ Series MP-11x & MP-124 Analog VoIP Gateways Version 6.6
Swisscom SIP Trunk Enterprise SIP using …
https://www.audiocodes.com/media/9703/ltrt-13160-mediant-bri-or-pri-gateway-for-swisscom-sip-trunk-configuration-note-ver72.pdf
Version 7.2 11 Swisscom SIP Trunk "Enterprise SIP Standard" 3 Configuring AudioCodes Media Gateway This chapter provides stepby--step procedures on how to configure the AudioCodes Media Gateway for interworking with the Swisscom SIP Trunk. The se configuration procedures are based on the test topology described in Section
MAXCS 8.0 AudioCodes Mediant-1000 TLS Configuration Guide
https://know.altigen.com/attachments/1195/AudioCodes-Mediant1000-TLS.pdf
Set SIP General Parameters Configure the gateway SIP parameters. 1. Select VoIP > SIP Definitions > General Parameters. 2. Set the following parameters: Set Enable Early Media to Enable Set Session Expires Time to 300 Make sure that SIP Transport Type is set to UDP Make sure that SIP TLS Local Port is set to 5061 3. Click Submit.
AudioCodes Mediant 1000 Configuration Guide
https://know.altigen.com/attachments/1113/AudioCodes_Mediant1000_MaxCS7.pdf
Mediant™ 1000B Mediant™ 800 SIP Protocol Deployment Note Deploying AudioCodes Mediant™ 1000B / 800 with AltiGen® MAX Communications Server 7.0 . December 2014 . Document #: LTRT-
Transferring the call - techdocs.audiocodes.com
https://techdocs.audiocodes.com/voice-ai-connect/Content/VAIG_Integration/call-transfer.htm
By default, when the SBC device receives information to transfer the call from VoiceAI Connect, the SBC translates the telephone number ('tel' URI) into a SIP URI ('sip:[email protected]'). For example, if the SBC receives "transferURL": "tel:+14077511320" from VoiceAI Connect , the SBC changes the 'tel' URI to "Refer-To: <sip:+14077511320@<IP Address of SBC>:5060>" in the SIP message.
Now you know Audiocodes Sip Parameters
Now that you know Audiocodes Sip Parameters, we suggest that you familiarize yourself with information on similar questions.
