Audio Parameters Cisco Ata 186

Cisco ATA 186 and Cisco ATA 188 Analog Telephone …

https://www.cisco.com/c/en/us/td/docs/voice_ip_comm/cata/186_188/3_0/english/administration/guide/sccp/sccp3_0/sccpaape.html

Configuring and Troubleshooting the Cisco ATA 186 …

https://www.cisco.com/c/en/us/support/docs/voice-unified-communications/ata-180-series-analog-telephone-adaptors/19083-ata-fax.pdf

Cisco ATA-186(sip) - support.catnextgen.com

http://support.catnextgen.com/assets/img/voice_gateway/file_config/cisco-ata-186.pdf

SIP Parameters Tone Parameters Audio Parameters Service Parameters Debug Parameters Services Phone Status Phone Service Call Hi Network Parameters Cisco ATA 186 (SIP) UseTFTP TftpURL Cfglnterval EncryptKey EncryptKeyEx DHCP Static1P StaticRoute 3600 static ip dhcp 17227 n 12 A 00000000000000 StaticNetMask 255255 255 0 NATIP NATServer NATTimer

ATA 186 and one way audio - Cisco Community

https://community.cisco.com/t5/ip-telephony-and-phones/ata-186-and-one-way-audio/td-p/1794759

Your ata configuration should look like the following: LBRCodec: 2 Audio Mode: 0x00150015 Connection Mode: 0x00002404 Please apply the above change and test. You can confirm if the rtp packet reaches the ata with a packet capture and wire-shark. Please be advised that ata do not support modem.

Tech Philosophy: Cisco ATA 186: Audiomode settings

http://www.techphilosophy.com/2008/02/cisco-ata-186-audiomode-settings.html

Cisco ATA 186: Audiomode settings It is sometimes useful to hard-set settings on an ATA to confirm what VoIP protocol it is using and to test CAC. You can also set things like DTMF transmission method, VAD, and fax CED tone detection. The default audiomode is 0x00150015 (0015 for one analog FXS port and 0015 for the other).

Configuring ATA 186 for Fax service - Cisco Community

https://community.cisco.com/t5/other-collaboration-subjects/configuring-ata-186-for-fax-service/td-p/230109

The factory default value for AudioMode is 0x00150015, which is to send DTMF out-of-band if remote end supports it. The following are the possible DTMF transmission selection. 0x00050005 = Sets both lines to always send DTMF inband 0x00150015 = Sets both lines to always send DTMF out-of-band if remote end supports it.

Cisco ATA 186/188 Configuration and Review - Callcentric

https://www.callcentric.com/support/device/cisco/ata

STEP 1 Connect your router with the supplied Ethernet network cable to the Cisco. Now connect your phone to the port labeled " PHONE 1 " on the back of the Cisco. Finally plug the supplied power cable into the Cisco. STEP 2 Wait 60 seconds after plugging your Cisco in. STEP 3

Cisco ATA 186 188 Setup and configuration Guide for …

https://www.inphonex.com/support/cisco-ata-configuration.php

ATA Passthrough Configuration - Voice Gateways

https://www.ccexpert.us/voice-gateways/ata-passthrough-configuration.html

The various configuration parameters and bits may vary from load to load. The specific parameter used to set each port for fax mode is the AudioMode parameter. This parameter is a 32-bit value, where the lower 16 bits apply to the first line, and the upper 16 bits apply to the second line. These two ports can be configured independently.

Cisco ATA186 & ATA188 - Whirlpool.net.au

https://whirlpool.net.au/wiki/iinetphone_ciscoata186