6v6 Audio Output Transformer

6V6 output transformer - Music Electronics Forum

https://music-electronics-forum.com/forum/amplification/guitar-amps/theory-design/938887-6v6-output-transformer

The OT is an Allen Amplification TO11C (9960737) with the following description : Heavy-duty upgrade output transformer for single-ended amps using a 6V6, 6L6, EL34 or dual 6V6 power tubes is custom wound in the USA by Heyboer to stringent Allen specifications. 8,000 ohm primary to 8 or 16 ohm secondary for use with a single 6V6.

DIY Push-Pull (PP) 6V6 / 6V6GT Tube Amplifier Schematic

https://diyaudioprojects.com/Schematics/DIY-Push-Pull-PP-6V6-Tube-Amplifier/

DIY Push-Pull (PP) 6V6 / 6V6GT Tube Amplifier Schematic This 6V6 amp was built following the push-pull (PP) EL84 / 6V6 Dynaco A-410 output transformer schematic. There are a few minor deviations from the original schematics. Instead of Dynaco transformers, Hammond 1608A audio output transformers and a Hammond 272HX power transformer were used.

Output Transformer advice for 6V6 Design | Telecaster ...

https://www.tdpri.com/threads/output-transformer-advice-for-6v6-design.1036609/

Output Transformer: 6V6 vs. 6L6 | The Gear Page

https://www.thegearpage.net/board/index.php?threads/output-transformer-6v6-vs-6l6.1244287/

Output Transformer: 6V6 vs. 6L6. Thread starter jonathansuhr; Start date Apr 6, 2013; jonathansuhr Member. Messages 1,026. Apr 6, 2013 #1 Disclaimer: I have worked on a lot of pedals, but have only dabbled my feet in the world of amp electronics. Sorry for my potentially dumb questions!

Transformer - Output, 8 W, Single Ended | Antique ...

https://www.tubesandmore.com/products/transformer-output-8-w-single-ended

The power tube is a single ended 6V6. Others indicated that this transformer should work for a 6V6, so I ordered it. I’m happy to say it works very well with my 6V6 circuit, with no modifications necessary. This xformer had a different primary winding resistance than …

Really Nice Output Transformers for 6V6 CHEAP. - Amps ...

https://www.harmonycentral.com/forums/topic/1893248-really-nice-output-transformers-for-6v6-cheap/

6P6P (6V6) Push-Pull Audio Amplifier

http://www.r-type.org/articles/art-272.htm

The amplifier Kit as advertised on ebay. The author has plans for a pair of mono-bloc 6V6 push pull amplifiers with Hammond output transformers and DC-DC converts for both heater supply and main HT - all powered from a 19.5 Volt 'laptop brick' switched mode power supply. While looking at ebay, the present amplifier kit caught the author's eye.

Buy Raphaelite 5.5K 5W Canned Output Transformer, Special ...

https://fw.cicig.co/product/yiyxjq7c2/raphaelite-5-5k-5w-canned-output-transformer-special-for-el84-6v6-headphone-amplifier-tube-amplifier-90hz-55khz-0-5db

Cheap Transformers, Buy Quality Home Improvement Directly from China Suppliers:Raphaelite 5.5K 5W canned output transformer, special for EL84, 6V6 headphone amplifier, tube amplifier. 90Hz 55KHz 0.5dB Enjoy Free Shipping Worldwide! Limited Time Sale Easy Return.

Output Transformer Impedance

https://www.radioremembered.org/outimp.htm

a set that needs a new output transformer. The average beam power output tube, such as the 6V6 requires a load of around 5,000 ohms, and the average speaker voice coil can vary from as low as 1 ohm to 8 ohms or more. So, how do we determine which of our output transformers will match that impedance range? With some simple

Output impedance of 6V6 and 6L6 | The Gear Page

https://www.thegearpage.net/board/index.php?threads/output-impedance-of-6v6-and-6l6.832991/

Two 6V6 or 6L6 power tubes with an 8 ohm output transformer hooked up to an 8 ohm speaker has an 8 ohm load." For example, I thought a princeton reverb 8 ohm transformer would be 4 ohms with 6L6 tubes? If so, do you really need to have a switch for the different transformer taps when you change power tubes, or does it matter that much? V